Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 111 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.Spindle nut torque (2WD models) I just did the brakes on my 01 2WD and repacked the wheel bearings while I was at it. My service manual says to tighten the spindle nut 12 ft pounds or less, loosen it 1/2 turn, then tighten it as specified in the torque specs section of the manual. The torque specs section of the manual says to tighten the nut ...Likes: 0. Received 13 Likes on 12 Posts. My Procedure: On all Ford vehicles I have owned I adjust the front wheel bearings thusly: Torque the spindle nut to ~15lb/ft and spin the wheel to set the bearing, then back off the nut 'til it's slightly loose without letting the wheel turn, then put as much finger torque on the nut as possible, align ...Ford Lug Nut Torque Specifications Ford Lug Nut Torque Specifications Here are Ford Lug Nut Torque Specifications. ... 2014 140 ft-lbs E-350 SD DUALLY CHASSIS / UNFINISHED 2003 - 2015 150 ft-lbs. E-450 DUALLY CHASSIS / UNFINISHED 2003 - 2015 150 ft-lbs. ... F-150 4WD / 235/75R15 1984 - 2000 100 ft-lbs F-150 ...The 5.0L Coyote engine block main bearings have 3 sets of fasteners that are used to ensure the bearings stay in place. The first set of fasteners are a series of bolts that screw down vertically into the inwards portion of the bearing caps. These fasteners should be tightened down to 10 ft-lbs and then 48 ft-lbs and finally a 90 degree turn.On the other hand, excessive torque can cause stress on the wheel studs, leading to potential failures. Therefore, it is essential to follow the manufacturer's recommended torque specifications. 2015 F150 Lug Nut Torque Specifications. To ensure you have the correct torque specifications for your 2015 F150, refer to the table below:2015 - 2020 f150 5.0L Torque Specs. Specs. Torque Spec. 2020 f150 Front End Torque Specs. ... F150 Front Wheel Hub Torque Specs : 129 ft-lbs F150 Front Brake Bracket Torque Specs : 184 ft-lbs ... The front suspension on the 15+ Ford F150's uses a coilover shock suspension. This means that the shock and coil spring are build as the same unit.I found something that said 12.5mm offset and 6.5" backspacing but not sure it is for this exact wheel, can someone verify? Thinking of some 20x9's with 0 offset and 5" BS coupled with 285/55R20's. Trying to figure out if that would work and how much lift, minimal hopefully, maybe 1" to 1.5".proper seating of the wheel hub to knuckle attachment. Improper torque can lead to wheel hub movement and allow potential damage to the wheel hub and surrounding components. Be sure knuckle is clean from rust and debris before hub replacement. The tire lug nuts should also be properly torqued to secure the wheel to the wheel hub. Improper torqueTorque wheel lug settingsTorque lug specs ford wheel nuts 2015 ford f-150 wheel lug nuts torque specs + torque patternWhats the lug torque on a 2008 ford f250 super duty 4x4. single rear wheel. Wheel lug torque settings.Awesome 2014 ford f150 lug pattern Torque f150 ford nut lug specs front suspension2002 ford f150 lug nut torque specs.Jun 18, 2016 · wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off. while your vehicle is in motion, resulting in loss of control. Bolt size lb.ft (Nm) M14 x 1.5 150 lb.ft (204 Nm) *Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford.Basically you tighten the lower balljoint nut to 35-40 ft-lbs. Install and tighten the upper nut to 85-100 ft-lbs. Then tighten the lower to 95-110 ft-lbs. I have a 1998 F-150 with a bad upper ball joint.need help with how much toque for the ball joint and how much toque for control arm. bdgormj.I believe you torgue the inner bearings to 40-50 lbs and the outer bearings to 140-150 lbs. You also to need to back of a quater turn after torquing down the lock nuts. The exact specs are in the haynes manual... You torque the inner nut to 50 ft-lb while rotating the hub to seat the bearings, then back off a 1/4 turn.Wheel size, PCD, offset, and other specifications such as bolt pattern, thread size (THD), center bore (CB), trim levels for 2022 Ford F-150. Wheel and tire fitment data. Original equipment and alternative options.It is pretty high for a 2wd. Installation. Position the brake disc on the spindle. NOTE: Tighten the spindle nut to the specified torque. Rotate the disc counterclockwise 5 rotations and then recheck the torque. Install a new spindle nut. Tighten to 400 Nm (295 lb-ft). Install the spindle nut retainer and a new cotter pin.Ford F150 14 (2021-on) Torque Spec Settings. By HJUdall - Own work, CC BY-SA 4.0. Below you'll find the tightening torques for the Ford F150 14 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.2015 ford f-150 wheel lug nuts torque specs + torque pattern2019 wheel torque Ford torque curve f150 ecoboost engine godzilla r2 5l power v6 turbo cummins vs diesel v8 rpm coyote option sourceF150 tires. 2019 wheel torqueF150 supercab 2wd Torque spec spindle 2000 nut wheel 4x4 ford 2010 abs let know help2009 f250 wheel torque values.75 ft-lbs. Stabilizer Endlinks Torque Spec. 75 ft-lbs. Shock Upper Nut Torque Spec. 66 ft-lbs. Shock Lower Nut Torque Spec. 66 ft-lbs. Leaf Spring Bolts Torque Spec. 173 ft-lbs.Last edited by edrobyn; 01-26-2021 at 08:59 PM. Maintenance Shop - Bearing & hub torque specs. 2015 F150 2WD - Need to replace the bearing/hub assembly and have looked all over for the torque specs for a 2 WD front bearing/hub assembly bolts , caliper, center spindle bolts and anything else I’ll need to tighten back after replacing.Research the 2015 Ford F-150 at Cars.com and find specs, pricing, MPG, safety data, photos, videos, reviews and local inventory. ... Rear-wheel drive. Drivetrain. View all 2015 Ford F-150 specs ...The following table provides the lug nut torque specifications for the 2015 Ford F150: How to Properly Torque Lug Nuts. To ensure the lug nuts are torqued correctly, follow these steps: Start by parking your vehicle on a flat and level surface. Loosen the lug nuts on the wheel you are working on using a lug wrench or a socket and ratchet.They are 6061-T6 billet aluminium. I had recalled reading a number of threads about torquing the adapter to the wheel at 150 ft-lbs. A buddy of mine and I did both our trucks, as we both ordered sets at the same time, so we just went with 150 ft-lbs, then put the tires/wheels back on and torqued to the normal spec of 150 for those too.The wheel lug nut torque for 2016 Explorer and Police Utility remains the same as the 2015 Model. The correct torque for the 2016 Explorer is 100 lb-ft (135 nm). The correct torque for the 2016 Police Utility is 110 lb-ft (149 nm). The Workshop Manual is being updated to reflect the correct torque specifications. Fitment: Vehicles with wheel ...For a 2020 truck caliper bolt torque is 55 ft-lbs and caliper bracket torque it 203 ft-lbs. This info is from the factory service manual. Reply Like. # 3. 02-10-2021, 07:56 PM. h20camper. Logistics Pro.The table below provides the lug nut torque specifications for the 2017 F-150 in both pound-feet (lb. ft) and Newton meters (Nm): Lug Nut Size. Torque Specification (lb. ft) Torque Specification (Nm) 14mm x 1.5. 150-165 lb. ft.Maybe just do 100. So now I'm stumped, I had a ford 'trained' mechanic tell me 150 so please help... Who to believe. Thanks. Well, I would believe the Owners Manual and then the Ford trained mechanic. For my 2014, the Owners Manual states 148 lb-ft for the wheel lug nut torque and that is the spec I follow. --KLG--.by SunnyFX4 » Mon Jan 22, 2007 2:49 pm. Somebody must have the torque specs for these trucks. I am going to call the dealership today, I will post up if I don't see anything here first. Ford Service indicates 150ft/lbs of torgue on the large 6 bolt studs. They upsized to 14mm Diam in 03 or 04, hence the heavy duty torque specs.Begin tightening the lug nuts in a star pattern. This ensures even distribution of torque and prevents warping of the wheel. Continue tightening until you reach the desired torque value. The torque wrench will click or provide a visual indicator when the correct torque is achieved. Repeat the process for each wheel on your Ford F550.The lower ball joint nut can be torqued down to 100 ft-lbs. And then the axle nut can be torqued to 225 ft-lbs. With the axle and lower control arm back in place you can reassemble the braking system and reinstall the wheel. Most of this is explained in other sections of this page and can be followed based on them.Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 122 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.2004 ford ranger front axle nut torque Ford f150 pickup torque specifications 1120 2003 instruction part fig motor 5.0 engine torque specs Specs torque ford f350 rear 1999 end sponsored links ... Ford hagerty tow poundsThe 2020 ford f-series super duty can tow 37,000 pounds Check that wheel torque!!2015 ford f-150 wheel lug nuts torque specs ...The Ford F150 is one of the most popular and powerful trucks on the market. It has been a staple of American roads for decades, and its reputation for reliability and performance i...2015 - 2020 f150 5.0L Torque Specs. Specs. Torque Spec. 2020 f150 Front End Torque Specs. ... F150 Front Wheel Hub Torque Specs : 129 ft-lbs F150 Front Brake Bracket Torque Specs : 184 ft-lbs ... The front suspension on the 15+ Ford F150's uses a coilover shock suspension. This means that the shock and coil spring are build as the same unit.The bracket can be torque down to 184 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 27 ft-lbs. Now we can move back to the center axle nut and torque it down to 30 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning.Once the turbo has been installed in place you can install the oil line and coolant line to the turbo and torque them down to 13 ft-lbs. The oil line to the engine block gets tightened to 31 ft-lbs and the coolant line to the engine block gets tightened to 13 ft-lbs. The exhaust downpipe tightens to 35 ft-lbs.Front Steering Torque Specs; Outer Tie Rod Torque Spec : 85 ft-lbs: Inner Tie Rod Torque Spec: 70 ft-lbs: Steering Box Bolts Torque Specs: 65 ft-lbs: Front Wheel Hub / Knuckle (2WD) Front Wheel Hub Bolts Torque Specs: 129 ft-lbs : Brake Caliper Bracket Torque Spec: 184 ft-lbs: Brake Caliper Slide Pin Torque Spec: 27 ft-lbs: Lugnuts Torque Spec ...1997 - 2003 F150 - 03 f150 xlt supercrew lug nut torque specs - I'm looking for the torque specs for the lug nuts on our 03 f150 with these types of rims. I searched online, and some people are saying 150 ft-lbs. However, the manual I found says 100 ft-lbs. I would really appreciate some feedback. Thanks!...One such component that requires specific torque settings is the lug nuts on your Ford F-150. Properly torqued lug nuts ensure the wheels are securely attached to the vehicle, preventing accidents and ensuring a smooth driving experience. In this article, we will provide you with the lug nut torque specifications for the 2015 Ford F-150.2016 Ford F-150 XIII (P552) [2015 .. 2017] ... Have a question about 2016 Ford F-150 wheel specs? Found a bug? Share your knowledge! ... (Nm) or foot-pounds (ft-lbs), wheel torque measures lug nut / bolts tightness. Ply Rating Ply rating denotes tire strength and load capacity, based on its layer count. Load Range.In the case of the 2016 F150, Ford has provided specific torque values that must be followed to ensure the wheels are securely fastened. This article will guide you through the recommended lug nut torque specifications for the 2016 F150, providing you with the necessary information to keep your wheels properly secured.Ford F150 13 (2015-2020) Torque Spec Settings. Kevauto, CC BY-SA 4.0, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 13 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.2015 - 2020 f150 5.0L Torque Specs. Specs. Torque Spec. 2019 f150 Front End Torque Specs. ... F150 Front Wheel Hub Torque Specs : 129 ft-lbs F150 Front Brake Bracket Torque Specs : 184 ft-lbs ... The front suspension on the 15+ Ford F150's uses a coilover shock suspension. This means that the shock and coil spring are build as the same unit.2013 Ford F150 Lug Nut Torque Specs Why Lug Nut Torque Matters. Properly torquing the lug nuts on your 2013 Ford F150 is crucial for the safety and performance of your vehicle. Insufficient torque can lead to loose or even detached wheels, while excessive torque can damage the wheel studs or cause the lug nuts to seize.180 newton meter = 132.7611865 pound foot. I'm assuming NM is newton meter. yes it is, thank you and there is the answer. The correct answer is 204 Nm, or (150 lb-ft). Thats right out of the Ford shop manual. 2004 - 2008 F150 - wheel lug nut torque specifications - i just got back from the dealership yesterday and while i was there i had ...Nov 16, 2022 · Ford F-150 Lug Nut Torque Specs. A lug nut torque spec is the amount of force it takes to properly tighten a lug nut on a wheel. This is a specification set forth by the vehicle manufacturer to ensure that the wheel stays secure to the vehicle. To ensure you get the right spec, you will need to use a torque wrench.Learn everything you need to know about spec homes in The Homeowner's Guide. Get insights on the buying process, financing options, and more. Click to read now. Expert Advice On Im...The following table provides the lug nut torque specifications for the 2015 Ford F150: How to Properly Torque Lug Nuts. To ensure the lug nuts are torqued correctly, follow these steps: Start by parking your vehicle on a flat and level surface. Loosen the lug nuts on the wheel you are working on using a lug wrench or a socket and ratchet.Thanks Spiky, I saved it in a safe place this time so I don't lose it again. 2009 - 2014 Ford F150 - Steering wheel nut - torque specs - I seem to have misplaced my service manual PDF, and the link that was being passed around here has been removed. To make matters worse, I found nothing while searching here or Google. SO, I ask the community.Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 122 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.Sep 21, 2019 · The manual calls for 150# for a reason, the engineers don't just pick a torque number for fun. And like I said in the other thread, if you can't handle 150#, don't buy a Ford Edge. Seems like Ford has revised this slightly. This is from 2016 OM. (not significant difference)The towing capacity of the Ford F150 varies by model, but the 2015 model ranges from 5,100 to 12,200 lbs. There are differences between how much an automatic and a manual transmiss...2016 Ford F-150 XIII (P552) [2015 .. 2017] ... Have a question about 2016 Ford F-150 wheel specs? Found a bug? Share your knowledge! ... (Nm) or foot-pounds (ft-lbs), wheel torque measures lug nut / bolts tightness. Ply Rating Ply rating denotes tire strength and load capacity, based on its layer count. Load Range.2015 ford f-150 wheel lug nuts torque specs + torque pattern. Torque lug specs nuts ford wheel2009 f250 wheel torque values Torque f150 ford nut lug specs front suspensionF150 tire fitment newer wheel 2009 guide leveled stx advance 4x4 br thanks un fit will.1997 - 2003 F150 - 03 f150 xlt supercrew lug nut torque specs - I'm looking for the torque specs for the lug nuts on our 03 f150 with these types of rims. I searched online, and some people are saying 150 ft-lbs. However, the manual I found says 100 ft-lbs. I would really appreciate some feedback. Thanks!...Technical Specifications: Length. 211.2 to 244.5 in. Fuel Capacity. 26 to 36 Gallons. Total Seating. 3 or 5 people. Drive Line: Driveline Type.Electronic 10-speed automatic features selectable drive modes - normal, tow/haul, snow/wet, eco-select and sport (standard with all-new 2.7-liter EcoBoost®, 3.5-liter EcoBoost and 5.0-liter V8 engines). Second-generation 2.7-liter EcoBoost now has advanced dual port and direct-injection technology.One such component that requires specific torque settings is the lug nuts on your Ford F-150. Properly torqued lug nuts ensure the wheels are securely attached to the vehicle, preventing accidents and ensuring a smooth driving experience. In this article, we will provide you with the lug nut torque specifications for the 2015 Ford F-150.2009 - 2014 Ford F150 - Brakes - Rear Caliper Bracket - Bolt Torque - I've seen that Torque specs have been covered a few times in reference to brakes but always in reference to the front. What about the rear? I'm currently changing rotors and pads using the Powerstop Z36 kit on my 2012 FX4. Does anyone know the...Using the proper torque helps ensure that the wheel assembly is securely installed. Using the manufacturer recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. ... Torque: FORD: 500: SEDAN / SE/SEL: 2005 - 2007: 100 ft-lbs: AEROSTAR: ALL / P195 ...To find out a wheel torque spec, check the vehicle’s manual, industry reference guide or the shop repair manual. Vehicle dealers can also provide an appropriate wheel torque spec. ...2015 ford f-150 wheel lug nuts torque specs + torque pattern. Torque lug specs nuts ford wheel2009 f250 wheel torque values Torque f150 ford nut lug specs front suspensionF150 tire fitment newer wheel 2009 guide leveled stx advance 4x4 br thanks un fit will.One of the leading causes of improper it or premature wheel hub failure is improper torquing of the bolts and nuts that secure the wheel hub and tire. Most drive axle wheel hubs have a center axle nut that must be torqued down onto the axle shaft to a speciic torque value. Putting the proper torque on the center1999 to 2016 Super Duty - 2015 F350 torque specs for front and rear brake pad and rotor replacement - I need to get the torque specs for my truck. I will be replacing the pads, not sure about rotors. I have a mechanic friend who is going to teach me how to do this, I paid a shop last time. Thanks 2015 F350 6.7 dually...2009 - 2014 Ford F150 - 2012 axle spindle nut torque value - Can anyone confirm 30 ft lb for the front axle nut? This is on a 2012 5.0 4x4. I can't seem to get a solid answer on this, some people are saying it's 295 ft lbs, but is that only for the 2 wheel drive?Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting in loss of vehicle control, personal injury or death. The tightening torque for the wheel lug nuts on a 2022 Ford F150 is 150 ft⋅lbf, or 204Nm (M14x1.5).Keep this example in mind. A typical air impact wrench generates 900 lb-ft of torque. In the case of a 2005 Mustang, Ford recommends using 100 lb-ft of torque to properly secure the car's lug nuts. You can do the math and imagine how easy it would be to over-torque this pony car's wheels using this tool.Originally Posted by All Hat No Cattle. Life is hard, good buddy. The spec for my wife's new Ford Edge is 162 lb/ft. Want to know how much a 0-250 torque wrench costs? You don't really want to know. Pfff. Everyone knows to use an air compressor wrench when it's more than 100 ft.lbs. Reply Like. 07-30-2018, 12:52 PM.I am serviceing a 2004 f-650 sd. i need to now the torque spec on the. 2015 ford f-150 wheel lug nuts torque specs + torque patternTorque lug wrangler f150 Ford f150 wheel nut torque specsTorque specs for ford f150 lug nuts. 2017 ford f150 lug nut sizeLug nut torque on 2018 f150 Lug nut torque. 2014 Ford F150 Lug Nut Torque.html | Autos PostMuch like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 111 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.2015 - 2020 Ford F150 - Actual horsepower of the F150 5.0 V8. ... you'd have to trust the Ford specs. Reply Like 07-03-2019, 09:30 PM ... Furthermore, the stock torque demand table only calls for 395-400 hp IIRC, so even if it's capable of more (it probably is) then the pcm won't let it make more. Reply Like 07-03-2019, 10:36 PM ...2009 - 2014 Ford F150 - Correct Lug Torque - Does anyone know the correct lug torque for a 2014 King Ranch with 20 Aluminium Wheels? ... Torque specs. Last edited by mastercct1; 03-03-2015 at 09:38 PM. Reason: duplicate posting Reply Like. 03-03-2015, 09:32 PM # ... One tire shop told me that they hand torque the lug nuts on every wheel. I ...It is pretty high for a 2wd. Installation. Position the brake disc on the spindle. NOTE: Tighten the spindle nut to the specified torque. Rotate the disc counterclockwise 5 rotations and then recheck the torque. Install a new spindle nut. Tighten to 400 Nm (295 lb-ft). Install the spindle nut retainer and a new cotter pin.Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 111 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.Torque 253 lbs.-ft. @ 4250 rpm 375 lbs.-ft. @ 3000 rpm 387 lbs.-ft. @ 3850 rpm 420 lbs.-ft. @ 2500 rpm ... 2015 FORD F-150 TECHNICAL SPECIFICATIONS Overall ratio 20.0:1 (122-in. and 141-in. wheelbase), 17.0:1 (145-in., 157-in. and 163-in. wheelbase) BRAKES Type Four-wheel vented discs, ABS Front 13.8 x 1.34 in., dual 2.1-in. pistons, non ...by gadams9090 » Fri Apr 29, 2005 3:00 am. well correct torque is 100ft lb silver, for if you use torque bars. by Offshore24 » Mon May 02, 2005 7:22 pm. After the recall in 99 Ford was using 100 ft-lbs torque for the aluminum wheels. My lug nuts have the torque requirement on them. by mike424 » Tue May 03, 2005 2:00 am.7. The Honda HR-V has a refined interior with lots of space, but it's dreary to drive with boring looks, so-so fuel economy and a lofty price, making it tough to recommend. Industry. 8. View All ...2015 - 2020 Ford F150 General discussion on the 13th generation Ford F150 truck. Sponsored by: 2016 Lug Nut Torque. Reply Subscribe . Thread Tools Search this Thread 11-09-2016, 02:49 PM ... Anybody know what the factory torque is on wheels/wheel spacers? I have some 1.25" spacers I need to install and thought I would see if any of you knew the ...Shop wholesale-priced OEM Ford F-150 Torque Converters at FordPartsGiant.com. All fit 1990-2019 Ford F-150 and more. ... 2015-2019 Ford F-150 | 6 Cyl 2.7L, 6 Cyl 3.5L GTDI | 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive) Less Info.Torque lug wheel ford spec specs nuts need nowF600 lug nut torque 2015 ford f-150 wheel lug nuts torque specs + torque pattern2013 ford f150 wheel torque specs. 2015 Ford F150 Lug Nut Torque Specs. Check Details. 2015 ford f150 lug nut torque specs. Ford f150 lug nut torque2012 ford f150 lug nut torque Torque lug1995 ford f150 lug nut torque specs.2-Speed Torque on Demand (Lariat+) with Flat Tow Mode ENGINES ... SPECIFICATIONS 2021 FORD F-150 *Available summer 2021. FORD F-10 TRANSMISSIONS 10-Speed SelectShift® Automatic 10-Speed Modular Hybrid Transmission ... ABS/Stability control Four-Wheel Anti-Lock Brakes, ...When it comes to maintaining your vehicle’s safety and performance, proper wheel installation is crucial. One often overlooked aspect of this process is the wheel lug torque, which.... 164 / 2700. Power / Horsepower. 325 HP @ 5750 rpm. Torque. 37For example, the 1993-1995 Lightning takes 100 lb/f Ford F150 14 (2021-on) Torque Spec Settings. By HJUdall - Own work, CC BY-SA 4.0. Below you'll find the tightening torques for the Ford F150 14 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find. 2015 - 2020 f150 3.5L Torque Specs. Specs. Torque Spec. 2017 f150 Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs.This article will provide you with the necessary information on the lug nut torque specifications for a 2004 Ford F150. By following these guidelines, you can ensure the safety and longevity of your vehicle’s wheels. ... Wheel Size Torque Specification (lb. ft) Torque Specification (Nm) 16-inch: 100-120 lb. ft: 135-163 Nm: 17-inch: 100-120 lb ... Here is a list of lug nut torque specs and sizes for...
Continue Reading